Skip to main content
8L Knowledge Base
Open a Support Ticket
Forums
Tormach YouTube
Tech Support YouTube
Tormach.com
Main navigation
8L Knowledge Base
Close navigation
Main
Open a Support Ticket
Forums
Tormach YouTube
Tech Support YouTube
Tormach.com
Main
About Your Machine
Safety
Machine Specifications
Machine Kinematics (Max Feed, Travel Limits, Accelerations)
8L Torque Curves
Site Requirements
Installation
Before You Begin and Move the Pallet
Unpack the Machine Crate
Assemble the Machine Stand
Lift and Move the Machine
Install the PathPilot Controller
Set Up the PathPilot Controller
Touch Screen
Touch Screen Installation Video
Touch Screen Installation Manual
Verify the Installation
Align Quick Change Tool Post Kit
Install the Machine Stand Coolant Kit
Maintenance
Machine Maintenance
8L Maintenance
Machine Paint Color Codes
Operation and Programming
Machine Operation
System Basics - 8L
PathPilot Interface Overview - 8L
PathPilot Tools and Features - 8L
Basic Operations - 8L
Install a Chuck onto 8L Lathe
ID Boring and Threading on a Tormach 8L
Changing Machine Configuration
Touching Off Drills on a Tormach Lathe
Setting Up Work and Tool Offsets on a Tormach Lathe
Setting Up Multiple Offsets on an 8L Lathe
Adjusting Lathe Soft Limits
Cutting a Thumbscrew on an 8L Lathe
Beginner's Guide to Lathe Tooling
Setting Start Line in the Middle of Program
Windows 10 Network Setup and G-Code Share
PathPilot Settings Backup
PathPilot Spindle Warm Up Program
Setting Up WiFi and Software Updates
Finding G-Code from the MDI Line
Generating a Log Data File in PathPilot
Setting Up a Boring Bar on an 8L Lathe
Tormach 8L Lathe Setup (Part 1): Setting Up Tool Heights and Lengths
PathPilot Programming
Programming - 8L
Macro Programming
PathPilot Post Processor Guidelines
G64/M59 Guide
Troubleshooting
Spindle and Drive System Troubleshooting
My Spindle Won't Turn
Motion System Troubleshooting
All Axes Won't Move When Commanded - 8L
One Axis Won't Move (or Only Moves in One Direction), and Other Axes Move - 8L
Controller and Console Troubleshooting
Controller Monitor (Standard and Touch Screen) Doesn't Work
No Ethernet Link Detected Troubleshooting - 8L
Operator Console Troubleshooting
Controller Won't Power On - 8L
Restore PathPilot to Factory Settings
PathPilot Controller CMOS Battery Replacement
General Electrical Troubleshooting
Checking a Fuse on a Tormach Machine
Machine Won't Power On - 8L
Flood Coolant Troubleshooting
Coolant Pump Won't Run
Diagrams and Parts List
Tailstock - 8L
X-Axis - 8L
Electrical Cabinet - 8L
Electrical Schematics
115 Vac Power - 8L (LA10506+)
24 Vdc Controls - 8L (LA10506+)
Axis Drive Bus - 8L (LA10506+)
Spindle Drive - 8L (LA10506+)
Machine Control Board - 8L (LA10506+)
Limit/Door Switches - 8L (LA10506+)
Accessory Power - 8L (LA10506+)
Grounds - 8L (LA10506+)
Grounds Terminal trip - 8L (LA10506+)
AC Terminal Strip (Before EMI1) - 8L (LA10506+)
AC Terminal Strip (After EMI1) - 8L (LA10506+)
Control Terminal Strip - 8L (LA10506+)
Limit Switches Terminal Strip - 8L (LA10506+)
Operator Console Schematic - 8L (LA10506+)
Breadcrumbs
Home
8L Knowledge Base
Operation and Programming
Machine Operation
On this Page
ID Boring and Threading on a Tormach 8L
https://youtu.be/LIwcwsCC4eI?si=1cYjzZr2JvOmqokn
